Complete notes on distillation for Class 9 from the NCERT Exploration textbook. Topics covered: definition and principle of distillation, the problem of separating miscible liquids, labelled distillation set-up (Fig. 5.12), step-by-step separation of acetone and water, fractional distillation of petroleum (Fig. 5.14b), the Deg-Bhapka method of Kannauj, and NCERT solved examples. Aligned with CBSE syllabus 2026-27.
Distillation is a method of separating a homogeneous mixture of two miscible liquids by heating the mixture until the liquid with the lower boiling point vaporises. The vapour is then passed through a condenser, cooled back into a liquid, and collected separately as a pure liquid called the distillate.
Distillation is the process of separating the components of a homogeneous mixture of two miscible liquids (or a liquid from a dissolved solid) by selective vaporisation of the more volatile component, followed by condensation of the vapour to obtain a pure liquid (the distillate).
Miscible liquids are liquids that mix completely in all proportions — for example, acetone and water, or alcohol and water. Because they form a single homogeneous layer, they cannot be separated using a separating funnel (which only works for immiscible liquids).
The principle of distillation rests on the difference in boiling points of the liquids in the mixture. Every pure liquid has a fixed boiling point at a given pressure — the temperature at which it converts from a liquid into a vapour. When a mixture of two miscible liquids is heated, the more volatile component (the one with the lower boiling point) vaporises preferentially at a lower temperature. The less volatile component (higher boiling point) remains in the distillation flask.
For simple distillation to give a reasonably pure product, the boiling point difference between the two liquids must be at least about 25 °C. When the difference is large enough, the vapour produced at the lower boiling point is almost entirely the more volatile component. If the difference is smaller than 25 °C, the vapour contains significant amounts of both components, and simple distillation does not achieve a clean separation — fractional distillation is required instead.
The NCERT Exploration textbook introduces distillation through a very practical scenario: a student accidentally mixed acetone and water in a beaker. Now how can the two liquids be separated?
This scenario illustrates an important point: the choice of separation method depends on the physical properties of the components of the mixture. For miscible liquids with different boiling points, distillation is the correct choice.
ApparatusThe NCERT Exploration textbook shows a labelled diagram of the distillation set-up in Fig. 5.12. Understanding each component and its role is essential for both conceptual clarity and examination questions.
Fig. 5.12 (NCERT Exploration): Distillation set-up for separating acetone from a mixture of acetone and water
| Component | Role / Function |
|---|---|
| Distillation Flask | Contains the mixture of acetone and water. Placed on wire gauze on a tripod stand over the burner. The flask has a side arm through which vapour exits. |
| Thermometer | Inserted at the opening of the side arm of the distillation flask. Monitors the temperature of the vapour passing out. When pure acetone is distilling, the reading stays steady at ~56 °C. |
| Water Condenser (Liebig Condenser) | An inclined glass tube surrounded by a water jacket. Cold water enters from the bottom (water inlet) and exits at the top (water outlet) — this countercurrent arrangement maximises cooling efficiency. Acetone vapour passing through the inner tube is cooled and condenses back to liquid. |
| Water Inlet / Water Outlet | Cold water flows into the condenser from the bottom (water inlet) and flows out from the top (water outlet). Countercurrent flow ensures that the coldest water is always in contact with the coolest vapour, giving maximum condensation. |
| Conical Flask | Placed at the outlet of the condenser. Collects the distillate — the pure liquid acetone that condenses from the vapour. |
| Wire Gauze | Placed on the tripod stand between the burner flame and the distillation flask. Distributes heat evenly and prevents direct flame contact with the glass flask. |
| Tripod Stand | Supports the distillation flask at a suitable height above the burner. |
| Laboratory Stand | Holds the condenser in the inclined position using clamps. |
| Burner | Provides the heat source to boil the mixture in the distillation flask. |
NCERT exercise question Q15 (Fig. 5.26) asks you to identify the separation technique shown and label apparatus A, B, and C. The answers are: A = Distillation flask, B = Condenser (Water condenser), C = Conical flask. The technique is distillation.
Let us trace exactly what happens when a mixture of acetone and water is distilled, using the set-up from Fig. 5.12.
Fig. 5.11 (NCERT Exploration): Basic distillation process — liquid → heating → vapour → cooling → liquid (distillate)
The boiling point difference between acetone (56 °C) and water (100 °C) is 44 °C, which is well above the minimum requirement of about 25 °C. This large difference means that when the mixture is at 56 °C, the vapour phase is almost entirely acetone — water hardly vaporises at this temperature. As a result, the distillate collected is very nearly pure acetone.
Distillation is not limited to separating two liquids — it can also be used to separate a liquid from a dissolved solid. For example, consider a solution of common salt (NaCl) in water:
In evaporation, the solvent escapes into the atmosphere and is lost. In distillation, the solvent vapour is condensed and recovered as a pure liquid. This is why distillation is preferred when both the solid solute and the liquid solvent are valuable products, or when pure solvent is required.
Simple distillation works well when the boiling point difference between two liquids is at least 25 °C. But what if the boiling points are close together — say, only 10–15 °C apart? The vapour produced at the lower boiling point would contain a significant amount of the other component as well, and simple distillation would give an impure product.
This is where fractional distillation comes in.
Fractional distillation is the process of separating the components of a mixture when the difference in their boiling points is less than 25 °C. A fractionating column is used between the distillation flask and the condenser. The fractionating column provides multiple stages of vaporisation and condensation, which progressively enriches the vapour in the more volatile component before it reaches the condenser.
A fractionating column is a tall glass tube packed with beads, rings, or other material that provides a large surface area. As vapour rises through the column:
This is essentially many simple distillations happening in sequence within a single column — making fractional distillation far more efficient than repeating simple distillation multiple times.
Real-World ApplicationThe most important industrial application of fractional distillation is the refining of crude petroleum. Crude oil extracted from the Earth's crust is a complex mixture of hundreds of compounds, primarily hydrocarbons, with different boiling points. A petroleum refinery (Fig. 5.14a) separates these into useful fractions using a giant fractionating column.
Fig. 5.14 (NCERT Exploration): (a) Petroleum refinery, (b) Products of fractional distillation of crude petroleum
| Fraction | Boiling Point Range | Collected From | Use |
|---|---|---|---|
| Petroleum Gas | Below 40 °C | Top of column (coolest) | LPG (Liquefied Petroleum Gas) — domestic cooking fuel |
| Petrol (Gasoline) | 40–75 °C | Upper part of column | Motor fuel for cars and motorcycles |
| Aviation Fuel / Kerosene | 150–250 °C | Middle of column | Jet fuel; also used as cooking fuel in kerosene stoves |
| Diesel | 250–350 °C | Lower-middle of column | Fuel for trucks, buses, diesel engines |
| Lubricating Oil | 350–400 °C | Near the bottom of column | Lubricating machinery, engines |
| Bitumen (Tar) | Above 400 °C | Bottom of column (hottest) | Road surfacing (tarmac), waterproofing |
Crude oil is heated in a furnace and pumped into a tall fractionating column. The column is hotter at the bottom and cooler at the top. Each fraction condenses and is drawn off at the level of the column where the temperature matches its boiling point. Fractions with the lowest boiling points rise highest before condensing and are drawn off near the top; fractions with the highest boiling points condense near the bottom.
The NCERT Exploration textbook highlights a beautiful example of traditional Indian science: the Deg-Bhapka method of distillation practised in Kannauj, Uttar Pradesh.
The Deg-Bhapka method is a traditional distillation technique used in Kannauj — known as the perfume capital of India — to extract fragrances from flowers, leaves, and even soil. The process uses simple copper vessels (deg = the still, bhapka = the receiver) connected by a bamboo pipe. Steam carries the volatile fragrance molecules from the plant material, and they condense in the bhapka to give a fragrant distillate.
Fig. 5.13 (NCERT Exploration): The Deg-Bhapka method of traditional distillation used in Kannauj
One of the most remarkable products of the Deg-Bhapka method is Mitti ka Ittar — literally, "earthy fragrance." This perfume captures the beautiful smell that rises from the earth after the first rains of the monsoon season (a smell caused by compounds like geosmin released by soil bacteria). Using the Deg-Bhapka method, artisans in Kannauj distil this fragrance by heating moist soil and collecting the steam condensate. Mitti ka Ittar is prized across India and exported internationally.
The Fragrance and Flavour Development Centre, Kannauj supports this traditional industry by providing modern institutional expertise. It assists farmers in growing fragrance-producing plants and guides entrepreneurs who wish to establish perfume businesses, linking ancient technique with modern science.
ComparisonThe following table compares the three separation methods covered in Section 5.3 of the NCERT Exploration textbook. This is a frequently asked comparison in examinations.
| Feature | Evaporation | Crystallization | Distillation |
|---|---|---|---|
| Used to separate | Solid solute from a liquid solvent | Pure solid crystals from a solution; purification of solids | Two miscible liquids, or a liquid from a dissolved solid |
| Product obtained | Solid residue (may be impure) | Pure, well-formed solid crystals | Pure liquid (distillate) |
| Solvent recovered? | No — escapes into the air | Can be recovered by subsequent distillation | Yes — collected as pure distillate |
| Purity of product | Lower (impurities remain in residue) | High (impurities stay in mother liquor) | High (nearly pure liquid collected) |
| Best used when | Only the solid is needed; purity is not critical | A pure solid is needed; small impurities must be removed | Pure liquid is needed; or both liquid components are valuable |
| Apparatus required | Evaporating dish, burner | Beaker, water bath, filter, watch glass | Distillation flask, condenser, conical flask, thermometer |
NCERT Q8: Two miscible liquids, A and B, are present in a mixture. The boiling point of A is 60 °C and the boiling point of B is 90 °C. Suggest a method to separate them. Also, draw a labelled diagram of the method suggested.
Method: Distillation
Reason: Liquids A and B are miscible, so a separating funnel cannot be used. Their boiling points are 60 °C and 90 °C respectively. The difference is 90 − 60 = 30 °C, which is greater than the minimum required difference of 25 °C. Therefore, simple distillation will effectively separate the two liquids.
Procedure: Pour the mixture into a distillation flask. Heat it. When the temperature reaches 60 °C, liquid A boils and its vapour passes through the condenser where it is cooled and condensed. The distillate (liquid A) is collected in the conical flask. Once all of A has distilled over, the temperature rises to 90 °C, and liquid B can be collected in the same way if required.
Diagram: Draw and label — Distillation flask (containing mixture A+B), Thermometer (showing 60 °C), Water condenser with Water inlet and Water outlet, Conical flask (collecting distillate A), Wire gauze, Tripod stand, Burner, Laboratory stand. Refer to Fig. 5.12 in NCERT Exploration.
NCERT Q (based on Chapter text): Why is distillation effective for separating acetone and water?
Distillation is effective for the acetone-water mixture because of the large difference in their boiling points:
This 44 °C difference is well above the minimum required difference of about 25 °C. When the mixture is heated to 56 °C, acetone vaporises almost exclusively while water remains in the liquid phase. The acetone vapour, when passed through the condenser, gives nearly pure acetone as the distillate. The water, being far less volatile at 56 °C, remains in the distillation flask.
NCERT Q15 (Fig. 5.26): Examine Fig. 5.26. (i) Identify the separation technique marked as 'S'. (ii) Label apparatus A, B and C. (iii) Which of the following mixtures can be separated by this technique? (a) water–acetone (b) water–salt (c) acetone–alcohol (d) sand–salt (e) alcohol–chloroform (f) alcohol–benzene. Use Table 5.5 data: Water 100 °C, Acetone 56 °C, Alcohol 78 °C, Chloroform 61 °C, Benzene 80 °C.
(i) Technique S = Distillation
(ii) Labels:
(iii) Mixtures that can be separated by distillation (boiling point difference ≥ 25 °C, and both components are liquids):
Q1. Define distillation. On what principle is it based?
Distillation is the process of separating the components of a homogeneous mixture of two miscible liquids by heating until the more volatile component vaporises, then condensing the vapour to collect it as a pure liquid (the distillate). It is based on the principle that different liquids have different boiling points. The component with the lower boiling point vaporises first at a lower temperature, leaving the other component behind in the distillation flask.
Q2. State whether the following statements are True or False. Correct the False statements.
(i) Distillation can be used for separation of two liquids even when these have the same boiling point.
(ii) Salt can be separated from a salt solution by evaporation or distillation.
(iii) Fractional distillation is used when the boiling point difference between two liquids is more than 25 °C.
(i) False. Distillation requires a difference in boiling points — at least about 25 °C. If two liquids have the same boiling point, they cannot be separated by distillation.
(ii) True. Salt can be obtained from a salt solution by evaporation (salt left behind) or by distillation (pure water collected as distillate, salt remains in flask).
(iii) False. Fractional distillation is used when the boiling point difference is less than 25 °C. Simple distillation is sufficient when the difference is 25 °C or more.
Q3. What is the role of the thermometer in the distillation set-up?
The thermometer is placed at the opening of the side arm of the distillation flask. Its role is to monitor the temperature of the vapour leaving the flask. When the distillation is proceeding correctly, the thermometer reading remains constant at the boiling point of the component being distilled (e.g., 56 °C for acetone). Once that component is completely removed, the temperature rises, indicating that distillation of the desired component is complete and the process should be stopped or the receiver changed.
Q4. How does a water condenser work? Why is cold water circulated in a direction opposite to the direction of vapour flow (countercurrent)?
A water condenser (Liebig condenser) consists of an inner glass tube through which hot vapour travels, surrounded by an outer jacket through which cold water flows. The vapour is cooled by the cold water jacket, loses heat, and condenses back into a liquid (the distillate) that drips into the collecting flask.
Cold water enters from the bottom and exits from the top — the opposite direction to the vapour flow. This countercurrent arrangement ensures that the coldest water always contacts the already-cooled vapour near the exit end, and warmer water contacts the hot incoming vapour at the entry end. This maximises the temperature difference between the vapour and the cooling water throughout the entire length of the condenser, giving more efficient and complete condensation than a co-current arrangement would.
Q5 (Application). A student boiled a mixture of alcohol (b.p. 78 °C) and water (b.p. 100 °C) and tried to separate them by simple distillation. Will the distillate be pure alcohol? Give a reason for your answer.
No, the distillate will not be pure alcohol.
The boiling point difference between alcohol (78 °C) and water (100 °C) is only 22 °C, which is less than the required minimum of about 25 °C. At 78 °C, a significant amount of water also vaporises along with the alcohol. The distillate will therefore be a mixture of alcohol and water, not pure alcohol. To obtain pure alcohol from this mixture, fractional distillation using a fractionating column is required.
Q6 (Application). Compare NCERT Q9: Compare evaporation, crystallization and distillation. In which situation would you prefer each method over the others?
Evaporation is preferred when only the solid solute is needed and purity is not critical, and the solvent does not need to be recovered. Example: obtaining salt from seawater in large open pans.
Crystallization is preferred when a highly pure solid is needed and the solid must be freed from small amounts of impurities. Example: purifying copper sulfate, obtaining white sugar from sugarcane juice.
Distillation is preferred when a pure liquid must be collected, or when two miscible liquids (with sufficiently different boiling points) need to be separated, or when the solvent also needs to be recovered as a pure liquid. Example: separating acetone and water; preparing distilled water from a salt solution.
Q7 (Application). The Deg-Bhapka method used in Kannauj is based on the same principle as laboratory distillation. What is that principle, and how is it applied in making Mitti ka Ittar?
The principle is that volatile fragrance compounds have lower boiling points than water. When moist soil or flower petals are heated with water in the deg (still), steam carries the volatile fragrance molecules into the condenser (bhapka). There they cool and condense, giving a fragrant distillate. Since the fragrance compounds are more volatile than many other components of the plant material, they are selectively transferred to the distillate.
In making Mitti ka Ittar, moist soil (which contains geosmin and other volatile compounds from soil bacteria) is the raw material. Steam distillation extracts these fragrant molecules, which condense in the bhapka to give the characteristic earthy perfume of the first monsoon rains.